Motorola GM950

Pildil on Motorola GM950 N3

Frequency range depending on version:	68-88 MHz, 136-174 MHz, 403-470 MHz
Mod               :            FM
RF Power output   : 5-25 W
Sensitivity       : <0.35 uV (12 dB SINAD)
Selectivity       : >60 dB (12.5 KHz), >70 dB (20/25 KHz) ETS
Image rejection   : >70 dB ETS
Voltage           : 10.8-15.6 VDC
Current drain     : RX: ? mA
TX                : Max ? A
Impedance         : 50 ohms
Dimensions (W*H*D): 168*44*160 mm
Weight            : 1.03 Kg
Manufactured      : 200x-200x
Other             : Select 5/5-tone selcall. CTCSS/PL. 128 channels
Split mounting option.

Specifications

Frequency Range: VHF: 66-88 MHz VHF: 136-174 MHz UHF: 403 470 MHz
Channel Spacing: 12.5 or 20/25 kHz
Memory channels: 14
Frequency Stability: +2 ppm (UHF); +5 ppm (VHF
Power Supply: 10.8 to 15.6V DC, negative earth
Dimensions: 44x168x160mm(HxWxD)
Weight: 1030 g
Operational Temperature: -25°C to +55°C
Storage Temperature: -40°C to +85°C
Antenna Connection: 50 ½ BNC
Environmental: - Mechanical IP54 Dust and Water
Protection IEC 68/2/27 Vibration IEC 28/2/6 Shock MIL-STD 810E Shock, Vibration and Crash Hazard*
Electrical ETS 300-086, ETS 300-113, ETS 300-219, ETS 300-279 (EMC)

TRANSMITTER

Channel Spacing: 12.5 or 20/25 kHz
Output Power: 5-25 W
Modulation Limiting: <+2.5 kHz (12.5 kHz); <+4 kHz (20 kHz); <+5 kHz (25 kHz);
FM Hum & Noise (CCITT): >40 dB (12.5 kHz); >45 dB (25 kHz) CCIT,
Conducted/Radiated Emission: <0.25 µW(0.1...1000 MHz); <1 pW (1...4 KHz)
Adjacent Channel Power <-60 db (12.5 kHz); <70 db (25 kHz)
Audio Response (300-3000 Hz): Flat or pre-emphasis
Audio Distortion: <5% @ 1kHz, 60% deviation
Transmit Turn On Time: <25 msec

RECEIVER

Channel Spacing: 12.5 or 20/25 kHz
Sensitivity: <0.35 µW (12 dB SINAD)
Intermodulation: >65 dB ETS >70 dB with base Option
Adjacent Channel Selectivity: >60 dB (12.5 kHz) >70 dB (20/25 kHz)
ETS Spurious Rejection: >70 dB ETS
Audio Distortion @Rated Audio: <5%
Hum & Noise (CCITT): >40 dB (12.5 kHz); ,45 dB (20/25 kHz) CCIT
Audio Response (3003000 Hz): Flat or de-emphasis
Co-channel Rejection: >12 dB (12.5 kHz); >8 dB (20/25 kHz) ETS
Conducted/Radiated Emission: <2 nW (0,1..1000 MHz); <20 nW (1..4 GHz)
Receive After Transmit Time: <25 msec
Audio Output Power: 4 W (internal speaker); <13 W external

Programming cable

The 16-pin accessory connector pin functions for the GM950 N3/N4 are as follow

Pin Name                   Type
--------------------------------------------------
1   SPKR- Analog           O/P
2   Ext. Mic Audio Analog  I/P
3   GP1 Digital            I/P
4   GP2 Digital            O/P
5   Flat TX Audio Analog   I/P
6   BUS+ Digital           I/O
7   GND Ground
8   GP3 Digital            O/P

9   GP4 Digital            I/P
10  Ignition Sense Digital I/P
11  RX Audio Analog        O/P
12  GP5 Digital            I/O
13* SW B+ Sense Analog     O/P
14 Hook Digital            I/P
15 RSSI Analog             O/P
16 SPKR+ Analog            O/P

*Factory default SWB+

PIN 1

Speaker- Audio. Speaker- and Speaker+ (PIN 16) are used to connect an external speaker. The audio PA is a bridge amplifier with a minimum load resistance of 3.2 ohms. The internal speaker can be easily disabled by removing the control head. Disconnect the internal speaker and assemble the control head back to the radio.

PIN 2

Microphone audio. This microphone signal input is common with the microphone singal input on the microphone connector and is connected to the microphone path input of the ASFIC. The nominal input level is 80mV for 60% deviation. The DC impedence is 1100 ohms and the AC impedence is 1000 ohms. Note: Only one microphone should be connected at any one time.

PIN 3

General Purpose 1 (GP1). This is a digital input only and is also available on the internal option connector (J0102:7). The RSS details which functions may be assigned to this pin by the codeplug. The primary use for this pin will be external PTT. (See Note 1).

PIN 4

General Purpose 2 (GP2). This is a digital output only. The RSS details whuch functions may be assigned to this pin by the codeplug. The primary use for this pin is as external alarm output. (See Note 3).

PIN 5

Flat TX Audio. This input is for injecting signals into the transmit path that should not be filtered, e.g. the output of a modem. The nominal input level is 150 mVRMS for 60% deviation. The impedence is greater than 25 kohms.

PIN 6

BUS+. This connects to the radio's SCI serial bus which is used for programming and tuning the radio. This line is also available at the microphone connector Pin 7.

PIN 7

Ground. Used as a ground for both analog and digital signals.

PIN 8

General Purpose 3 (GP3). This is a digital output and is also available on the internal option connector (J0103:7). The RSS details which functions may be assigned to this pin by the codeplug. (See Note 2). This output is shared with the serial bus data line. It can be used as a normal output, but will be overridden by serial data when the programming lead is plugged in. To restore general purpose output operation, the programming lead must be removed and the radio turned off, then on again.

PIN 9

General Purpose 4 (GP4). This is a digital input only. The RSS details which functions may be assigned to this pin by the codeplug. (See Note 1). This is a special input that will force the radio to turn on when it is grounded. This can be used for any input function, but is usually used for emergency.

PIN 10

Ignition Sense. Connecting this line to the ignition line of the vehicle will automatically turn the radio on when the ignition of the vehicle is turned on. When the ignition is connected, the radio cannot be turned off as long as the ignition is active. When this line is at 0V or is not connected, power on/off is under manual control. Resistor R0423, 4.7 kohm, which is not fitted as standard will cause the radio to be permanently on whenever 12 V is connected to the main power connector.

PIN 11

RX Audio Discriminator. The signal routed to this pin is controlled by ASFIC and gives continuous discriminator audio. For discriminator audio, the normal output level is 330 mVRMS for 60% deviation. The impedence is 600 ohms.

PIN 12

General Purpose 5 (GP5). This is a digital input/output and is also available on the internal option connector (J1003:3). The RSS details which functions may be assigned to this pin by the codeplug. (See Note 1 and Note 2).

PIN 13

Switched B+ Sense. The output of this pin may be configured by a solder link within the radio. Switched B+ is the default. The current limiting resistor R0455 default is 0 ohms, therefore, extreme care must be taken to avoid short circuiting this output to ground, which will damage the radio. The maximum continuous current allowed is 300 mA. A suitable external fuse must be installed into the lead to Pin 13 to avoid damage to the radio.

PIN 14

Hook. This port reads "0" when the microphone is on-hook, and "1" when the microphone is off-hook. It is assumed that the hook is a mechanical switch, so the software will always debounce this input. Also available on the microphone connector pin 3.

PIN 15

RSSI. Received Signal Strength Indication, buffered analog voltage.

PIN 16

Speaker+ Audio. Positive output of radio's PA (see PIN 1).

Note 1: Digital Input

4.7 kohm Internal Pull Up Resistor to +5 V,
Maximum Input Voltage accepted as Low = 0.6 V
Minimum Input Voltage accepted as High = 3.0 V

Note 2: Digital Output

4.7 kohm Internal Pull Up Resistor to +5 V,
Maximum Current when Output Low = 10 mA
Maximum Voltage when Output Low = 0.5 V @ 10 mA

Note 3: High Current Digital Output

4.7 kohm Internal Pull UP Resistor to B+,
Maximum Current when Output Low = 200 mA
Minimum Voltage when Output Low = 1.7 V @ 200 mA

Microphone Connector Details

PIN Name             Type
-----------------------------------
1   N/C
2   N/C
3   Mic Hook Digital I/P
4   Ground Ground
5   Mic Audio Analog I/P
6   Mic PTT Digital  I/O
7   BUS+ Digital     I/O
8   Handset Analog   O/P

Välised lingid